Site icon Real Relax Massage Chairs

Massage Chair Buying Guide 2022 – Full Detailed Guide

Massage Chair Guide

Massage Chair Guide

Chair Component

  1. Pillow
  2. Shoulder massage part
  3. Back cushion
  4. Hand and arm massage department
  5. Seat cushion
  6. LED lights
  7. Footrest

Set up a massage chair

Installation location.
• Make
 sure there is enough space to recline.
• Do not expose the massage chair to direct sunlight or high temperatures, such as in front of a heat source, as this will cause the synthetic leather to discolor or harden.
• Place the device on a mat to prevent damage to the floor.
• When placing a cushion under the device, the size of the cushion should be large enough to cover the area that the device touches and the area where the leg rest may touch the floor, as shown in the figure above.
• Install the device near a power outlet.

Preparation before use

Check the space around the product.
Make sure that there are no people, pets, or other objects near the product. Make sure that there are no foreign objects at the seams of the product. Before sitting on the product, make sure that there are no foreign objects between any two parts of the product. Do not put your hands, arms, or head between the backrest and the back cover.
Do not place pets on the product (such as the back cover, backrest, and armrests).
Turn on the product power
Push the power connector into the electrical socket until the end.
Insert the power plug into the power socket until the end. Turn the switch to the “I” position
Make sure that the massage roller is retracted.
If they are not, press the NO button to return them to the retracted position.

How to use

Controller

product operation guide
Turn on the power, turn the switch to the “I” position, the chair enters the idle mode, the backrest angle reaches the highest position, and the pedal angle reaches the lowest position. In idle mode, only five functions can be operated: ON/OFF, tilt, tilt, tilt leg, tilt leg.

Switch
Start/Stop control button
Press this button once, the LCD backlight and ON/OFF button will light up. Press any massage function button to start the massage function of the chair. This will also start the timer function. Press this button again to stop all massage functions, and the massage rollers, backrest, and leg rest will return to their original positions.

Pause Pause
button When the massage chair is in massage mode and the user wants to temporarily pause, press the pause button, and all massage functions will stop. The “Pause” button will flash, and the countdown of the set time will also be paused. Press the pause button again to resume the original massage function, and the countdown of the set time will continue.

3D adjustment
Press 3D+/3D- to adjust the 3D roller forward/backward respectively. There are 3 different levels for adjustment to suit different massage intensity requirements.

Automatic program

If one of the automatic programs is activated, the chair will automatically scan the shoulder height. The theme will automatically enter the shoulder adjustment, and the user can manually adjust the shoulder height position to the desired comfortable position before the automatic program starts. The
following are the available automatic programs:

  1. Neck/shoulder
  2. strengthen
  3. relax
  4. Thai
  5. recover
  6. Sleep

Tilt leg/ Tilt leg
Foot pedal angle adjustment control buttons
These two control buttons can adjust the massage angle on the footrest.
Press the tilt leg or tilt leg control button once, and the foot pedal will start to move; when the foot pedal reaches the desired comfortable position, press the button again to stop it.

 zero gravity 

In Zero Gravity by default, press this key to start the zero G1 function, press this key again to start the zero G2 function, and press this key again to return to the idle position.
Note: If you press this button while moving to zero-G1, the massage chair will stop at the latest angle. If the zero-G button is not pressed when moving to zero-G1, the massage will stop at the preset zero-G1 angle. The same conditions apply to the zero G2 function.

Backrest tilt/tilt

Massage chair angle adjustment control button
These two controls! The button can adjust the tilt/tilt angle of the backrest separately. Press the tilt or tilt control button once and the backrest will start to move. When the backrest reaches the desired comfortable position, press the button again to stop it.

Manual massage function
Kneading, Tapping, Swedish, Shiatsu, tapping, rolling
Press this button to activate the rhythmic kneading manual massage function for a full back massage with moderate intensity. Each time you press this button, the manual massage function will change in the order of kneading> tapping> Swedish> acupressure> tapping> rolling => stop.

Manual massage function direction

When the manual massage function is running, press this key to switch the rhythm mode of manual massage between 1 and 2.

Speed
backrest adjustment button-5 speeds adjustable. After the manual massage function is turned on, each time you press the button, the speed can be adjusted from weak to strong.

Width adjustment
Back massage width adjustment button-3 levels available. After
activating the tap, clap, shiatsu, or scroll functions, the user can touch the button to adjust the massage width. There are 3 levels available (narrow, medium, and wide).

Spot/Partial
Partial or Partial Back Massage
This button allows the user to select a point massage for any part of the back.
Press this button once to activate the point massage at the desired location.
Press this key again to switch to some functions.

Up/down
massage position adjustment buttons for partial and partial massage.
When the manual or automatic shoulder scanning cannot meet individual needs, you can manually fine-tune the shoulder height position by pressing the up’ down button within 10 seconds of the sound. Once you find a suitable position and release the key, the final position will be locked.
Note: During the partial or partial massage, you can also use these two buttons to adjust the massage position.

Heat
Each time you press this button, the thermal massage function will change in the order of mechanical heating>knee/leg heating>mechanical/knee/leg heating>stop.

Whole-body air pressure massage
Whole-body air pressure massage
Press once to start the whole body air pressure massage, press again to stop the function.

Manual air
setting Air squeeze
Each time you press this button, the manual air massage function will change in the order of EGREST>ARMREST>SHOULDER=STOP.

Brightness
pressure intensity adjustment button-5 levels of intensity can be adjusted.
After activating the air pressure function (automatic and manual), press this button to adjust the intensity in the loop.


Start/stop control buttons for the casters and casters
Press once to activate the casters, and press again to stop the casters.
End the operation After
use, please press the “ON/OFF” button, the massage chair stops running, and the massage roller returns to its original position; then switch the power button under the chair to the “O” position and unplug the machine from the power socket.

Keep these instructions

Note: This lipstick is very soft, it is recommended to put it into XNUMXmm or XNUMXinch when applying) The
user’s weight is usually limited to 220 pounds. For people weighing 220 pounds or more, product operation may produce more noise and the fabric cover may wear out faster.

FCC Radiation Exposure Statement: (mobile device)

To avoid the possibility of exceeding the FCC radio frequency exposure limit, the distance between the human body and the antenna during normal operation must not be less than 20 cm (8 inches).

FCC statement

The operation must meet the following two conditions: This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause an unexpected operation.

This device has been tested and found to comply with the limits for Class B digital devices in Part 15 of the FCC Rules. These limits are designed to provide reasonable protection from harmful interference in residential installations.

This equipment generates, uses, and radiates radiofrequency energy, and if it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.

Industry Canada announcement
This device complies with Industry Canada’s license-free RSS standard. The operation must meet the following two conditions: This device may not cause interference.

This device must accept any interference, including interference that may cause the device to operate unexpectedly. Changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.

Synthetic leather cleaning
wipe synthetic leather with a soft, dry cloth. Do not use chemicals such as thinner, gasoline, and alcohol to clean the product. When using commercially available leather care products (cleaning cloths), please follow the instructions for use.

If the synthetic leather is very dirty, wipe it with the following method. Put a soft cloth in water or hot water containing 3% to 5% neutral detergent and wring it out. Wipe the surface of synthetic leather with a soft cloth.

Use a cloth soaked in clean water and wrung out to wipe off the cleaner. Wipe with a wrung soft cloth.

The synthetic leather is air-dried naturally. If the stains on synthetic leather are difficult to remove, immerse a commercially available melamine foam sheet in a neutral detergent, and then use a wiping product. Do not use a hairdryer to dry the surface.

The surface of synthetic leather can be dyed with the color of the fabric; therefore, be careful when wiping the product with denim or colored cloth. Synthetic leather may be discolored, so the area in contact with the hair dye should be covered with a towel.

Cleaning of plastic parts
1) Dip a soft cloth in water or neutral detergent, wring out and wipe the plastic parts.
• Do not use chemicals such as thinner, gasoline, and alcohol to clean the product.
2) Wipe with a cloth soaked in clean water and wrung out.
• Wring the cloth dry before wiping the remote control with a cloth.
3) Let the plastic parts air dry naturally.

Troubleshooting

This page summarizes the most common problems you may encounter when using this product. If you cannot solve the problem with the following information, please contact the service center immediately.

If the problem you are experiencing is not listed, please try the following suggestions:

  1. Turn off the product and unplug it.
  2. Wait 60 minutes.
  3. Plug the product back into the recommended socket and restart it.

Grounding instructions

You Can Also Read My Related Article About Real Relax Massage Chair:

Real Relax 2021 Massage Chair Review 2022

Real Relax 2020 Massage Chair Review 2022

Real Relax Massage Chair Review 2022

Exit mobile version